Received item on obdii365.com 7 days after initial order, so not bad
To start with the software installation can be a little problematic to the point I Installed upto V96 only, however as I am using on an 2006 Fiesta it more than adequate for my needs.
I purchased the device because I needed to program an ebay purchased key to the vehicle PATS system as I only had one key when I brought the car and really wanted a spare in case of loss or damage
The device was able to delete all old keys from the system then and add 2 new keys, whilst I was there I did some software updates on the PCM.
Honestly it really is a good device and works perfectly once you get over the software issue.
A bit of advise with the software is use virtual machine (its easyier to delete and start again), and follow video guides found on youtube
Here is a quick guide for my success:
Use Virtual machine installer found on Ford IDS CD V97, install VM then create a VM
Then on the virtual machine
Install calibration from V81 CD
Install V91 from V97 CD and reboot without opening software
Once rebooted open software and agree to 3 day licence, enter any details
Close software and Install V96 and reboot without opening
Once rebooted you can open software
Install software on CD V97 for the VX device
At this point I just installed deep freeze found on cd V97
Still playing with the vxdiag scanner, will report the test results in few days.
VXDIAG VCX NANO for Ford&Mazda 2-in-1 IDS software has newly updated to V98. Obd365 here provides the free V98 Mazda IDS version. V98 Ford IDS version will be added soon.
PS. If you had Ford VCMII (SP177-1,SP177-C), you can download Ford IDS V98 free as well here is the link http://www.chinaautodiag.com/html/ids-v98-free-download-23541.html
Here is the instruction on how to install Tech2Win 11.27 software for VXDIAG VCX NANO GM/OPELscanner. And also, obd365 technicians tested/ diagnosed VXDIAG VCX NANO GM on North American BUICK (A)2010 passenger car, via WIFI wireless or USB connection.
Operating system: Windows XP, Win7, Win8 32bit and 64bit
Language: English
VXDIAG GM Tech2Win Video guide:
STEPS:
Preparation
Step 1 install MDI
Step 2 install Tech2Win
Step 3 install VX Manager
Step 4 local network connection
Step 5 install GM GDS2/Tech3
Step 6 Tech2Win-Wired diagnosis on American BUICK 2010
Step 7 VCX-WiFi connection
Step 8 Setup Wlan connection in VX Manager
Step 9 Tech2Win-Wireless diagnosis on American BUICK 2010
Here’s an easy instruction on how to how to perform Operator Commanded Regeneration (OCR) withFord VCM II or VXDIAG VCX NANO IDS system manually.
When to perform OCR Use the OCR feature when the DRIVE TO CLEAN EXHAUST FILTER message appears in the message center and: • the operator is not able to drive in manner that allows effective automatic cleaning (active regeneration), • or the operator instead wishes to manually start regeneration (cleaning) of the DPF while the vehicle is idle (stationary).
Tool to use:
Ford VCM 2 or VXDIAG VCX NANO for Ford& Mazda 2-in-1
(better operate in Windows XP or VMware)
Procedure:
In IDS, Select Toolbox-Powertrain-Service Funtions-DPF manual regeneration
also, keep drilling down to Diesel particulate regeneration system- DPF manual regeneration.
One or both of those will be changed to “Yes”
Go to the gauge display on the IC, and the regen % will be on the third page. The 4th will still be blank.
I haven’t dicked around with it in awhile, but I’m sure that I will be able to OCR in the near future without going through the Edge module.
VXDIAG VCX NANO for Toyota TIS (USB and WIFI version) diagnostic scan tool supports diagnostic tests, programming matching, custom functions, the key matching, etc. The newest software V10.10.018 supports the Toyota models till 2015. VCX is a standard SAE J2534 Pass-thru programming tool, which can do online ECU programming.
Software version: Techstream V10.10.018
Language: English, French, Italian, Spanish, German, Chinese
Support Toyota models till year 2015 (12V and 24V cars, heavy truck and diesel)
Top feature:
Fully compatible with SAE J2534;
Adapters and cables with self-determination;
Fits CE and FCC hardware;
Firmware can be updated online.
How to install VXDIAG VCX NANO for Toyota TIS?
Step 1: Install Techstream
Open My Computer
Open NANO TOYOTA software CD
Make sure the computer time is the same as your local time
Open Techstream-Setup-10.10.018
Select software language, click Next
Install Techstream software wizard, click Next
Accept license agreement
Click Next
Confirm user name and company name, press Next
Click “Install”
The procedure will take 10 minutes, please wait patiently
Step 2: Activate Techstream
This will create Tecshtream software shortcut on desktop
Right click Tecshtream software on desktop, click Properties>>Find Target, go to C:\Program Files\ToyotaDiagnostics\Techstream\bin\VerApp.ini, change TISFunction=1 to TISFunction=0, save it.
